Showing results: 871 - 885 of 1675 items found.
-
Huntron
Flying Probe technology is used to automate the testing of printed circuit boards (PCB) that would otherwise have to be tested manually. Adding a Huntron Access Prober to your test procedure will significantly decrease test times therefore increasing productivity.Access Probers can accurately place a probe on test points with high accuracy achieved using micro-stepping motors and linear laser encoders. Probing the smallest surface mounted devices is possible. Huntron Access Probers can automate your unique test process using the standard probe or by adding a custom probe of your design. Huntron offers three Flying Probe system configurations based on PCB size and test head requirements.
-
Data Patterns Pvt. Ltd.
VXI stands for VME eXtensions for Instrumentation. It is an open standard first developed by five leading Test and Measurement companies in 1987 to standardise a backplane capable of developing open, interchangeable instrument modules that could be used to build Automatic Test Equipment (ATE).Data Patterns designs and markets a wide range of VXI modules, some of which are listed below. Due to the use of the latest technologies, Data Patterns VXI modules offer the highest I/O density available in the industry today.Further enhancements of functional capabilities are achieved by the use of VXI IP carriers and VXI M Module carriers. This extends standard functions available from Data Patterns in these mezzanine architectures to the VXI platform.
-
Guangdong Bell Experiment Equipment Co.,Ltd
Walk in chamber for Complex Salt Spray Test Relevant standards requirement1. Test Object: battery pack andsystem.2. Refer GB/T4 part 5.5.2 test method, test according to GT/T2423.17 test conditions.3. The salt solution was made up with sodium chloride (chemically pure and analytically pure) and distilled or deionized water，Its concentration is (5 + 1)% (mass fraction).4. (35 ± 2) ℃, the measured pH value is between 6.5-7.2.5. Placed the test objects in the salt spray chamber for cycling test. Each cycling duration for 24h. Spray salt solution to the test object for 8 hours under the temperature of (35± 2) ℃ , remain for 16 hours. Between the forth and the fifth hour in one cycles should be according to test requirement in GB/T 28046.1-2011, test mode with 3.2.6. Total 6 cycles testing.7. Salt spray test is not necessary for the test objects being installed in passenger, luggage or cargo compartments.
-
ISequenceSpec -
Agnisys, Inc.
The complexity of modern SoC has raised the requirement for HW/SW co-simulation to catch the bugs from the early design stage. There is lack of common set of sequences which can be shared across the teams. ISepenceSpec helps design teams to generate the unified test and programming sequences in UVM and Firmware from the specification. ISequenceSpec uses the register information from importing the standard formats like IP-XACT, SystemRDL, XML. User can define the test sequences in a simple editor, and then generate the unified test sequences from verification to validation.
-
HIL 6 series -
Typhoon HIL, Inc.
With 20 ns PWM sampling time, down to 500 ns simulation time step, and ultra-low latency, 6 Series processor has set the industry standard for ultra-high fidelity real-time emulation of power electronics systems. Simply plug your controller into a Typhoon HIL 6 Series real-time emulator, without any controller modifications, and take it for the most demanding test drive ever. Test any and all imaginable operating conditions, including faults. Automate and formalize test processes with our integrated software tools.
-
Bitbar Inc
Selenium has already cemented its place as a de-facto web test automation standard and Appium is providing very clean high level API that can be quickly adopted by Selenium developers, as it nicely abstracts lot of the messy stuff related to running tests. Our Testdroid Cloud provides this sort of environment where everything is packaged and pre-build for your Selenium / Appium tests, using only real mobile devices (Android and iOS) and real browsers that are usable with those devices (Safari for iOS, Chrome, WebKit, Firefox and others for Android).
-
TA-3C -
Tech-Aid Products
The TA-3C test fixture is a combination of the KMD540 testing requirements and the RDR-2000/2100 weather radar interface requirements. This panel allows the technician to test the KMD540 MFD as a stand alone item (with external simulators) or together with a radar sensor for a dynamic real time test. The panel includes the required switching for sensor alignment and KMD testing along with input jacks for the required data inputs. Also built into the fixture is an analog gyro simulator for checking the stabilization functions of the sensor. The full enclosure comes in standard panel width.
-
Bloomy Controls, Inc.
The Energy Storage System (ESS) Performance Test System is used to evaluate, test, and certify the performance of energy storage systems up to 2MW. The system is a configurable platform with over 200 channels of simultaneously measured AC and DC voltages and currents, environmental temperatures, airflow, and communications. Intuitive software provides real-time monitoring and analysis of power, energy and efficiency to adhere with industry standards. The test system interfaces hardware such as load banks, and controls the ESS to simulate utility applications such as peak shaving and frequency regulation.
-
LX-30A+ -
Shenzhen Lian Xin Technology Co., Ltd.
Meet UL, VDE, CSA, SAA, T-MARK, KS. IRAM, CCC and other countries’ standards .．·used to test single – ends ,double –ends ,three-ends power supply cords.．·Auto and continuous test in COND,Insulation Resistance ,Leakage Current, Line-to-line Hi-pot(inside HV), Leaking copper(outside HV), relative length,．·Auto test the fine and detective goods, tested qualified ones can be be ejected by ejector pin and marked , automatic cutting defective products， and alarmed with voice prompt and light,
-
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
-
M9120A -
Keysight Technologies
The M9120A high-density matrix offers higher voltage switching of multiple channels in a single instance. Any row can be connected to any column, making it ideal for routing instrument signals to the device under test. This 2-wire switch matrix provides the durable armature switches allowing multiple channels to be connected at one time, up to 60W per channel. The 4-wire wide bus can be used to route signals between test instruments and the device under test. Choose from the durable connector block or standard cable connections.
-
787047-01 -
NI
12 GHz, 1 GHz Bandwidth PXI Vector Signal Transceiver - The PXIe-5830 supports validation and production test into mmWave frequency bands. This vector signal transceiver incorporates a vector signal generator, vector signal analyzer, and high-speed serial interface with FPGA-based real-time signal processing and control. The PXIe-5830 helps you test a variety of cellular and wireless standards such as Wi-Fi 6. You can expand a test system in the PXI Express form factor to support multiple input, multiple output (MIMO) configurations with phase-coherent synchronization.
-
ADTS-2000 -
TestVonics, Inc.
TestVonics ADTS-2000 Test Set is a portable, high precision, dual channel air data pitot static test system. This tester is designed to calibrate, test and troubleshoot air data instrumentation and aircraft pitot-static systems. The ADTS-2000 meets all requirements of the KTS-2000 , P/N: 18910920000, P/N: 18910920001, P/N: 18910920002, or having NSN: 4920-01-588-4428 and NSN: 4920-01-554-4549 . The test set has been designed with functional and reliability features highly suited to withstand the harsh environmental and demanding conditions of the flight line environment. The test set is designed for testing a wide range of commercial and military aircraft, both rotary and fixed wing. The ADTS-2000 accuracy complies with standards for RVSM and is designed to replace the TTU-205 test set.
-
Chroma ATE Inc.
AC power source 61500 series sets up the new standard for high performance AC power source. It equips with all powerful features such as power line disturbance (PLD) simulation, programmable output impedance, comprehensive measurement functions, wave-shape synthesis and regulation test software.
-
EV-TEST100 -
HT Italia Srl
EV-TEST100 in combination with appropriate HT multifunction instrument simulates an electric vehicle connected to the charging station, allowing you to verify the EVSE full functionality and electrical safety. EV-TEST100 is able to test charging stations with charging modes 2 and 3 and Type 2 connector (European standard).
